Loading Pond Liner Calculator...
v3.0
Draw your pond above and enter its deepest point. The calculator tells you the liner size to order, adds underlayment to go under it, and prices it in EPDM or RPE. Add a stream or waterfall and it sizes those liner pieces too. This guide shows the math, so you can check any answer by hand.
How to calculate pond liner size
A flexible liner has to cover the bottom of the pond, run up every wall, and lap onto the ground around the edge. So each side of the liner is:
Liner length = pond length + (2 x deepest point) + (2 x edge overlap)
Liner width = pond width + (2 x deepest point) + (2 x edge overlap)
Use the deepest point, not the average depth. The calculator adds 18 inches (1.5 ft) of edge overlap on every side, and you can change that to 2 or 2.5 ft in its settings. L-shaped and free-form ponds get 1 extra foot each way, because the liner has to follow curves and inside corners. The answer is then rounded up to the next 5 ft, the steps liner sheets are cut in.
Worked example
A 12 x 10 ft koi pond that is 3 ft at its deepest point:
- Length: 12 + (2 x 3) + (2 x 1.5) = 21 ft, rounded up to 25 ft
- Width: 10 + (2 x 3) + (2 x 1.5) = 19 ft, rounded up to 20 ft
You need a 20 x 25 ft liner (500 sq ft) and the same size of underlayment.
Do plant shelves or sloped sides change the size?
No. Measuring to the deepest point already covers them. On a pond with straight walls and plant shelves, the formula is exact: the liner that runs across a shelf is liner the bottom no longer needs. Sloped walls take a little less liner than straight ones, so the formula leaves you some to spare.
How to measure your pond for a liner
- Length: the longest distance across the top of the hole.
- Width: the widest distance at right angles to the length.
- Depth: the deepest point, measured down from the top edge of the pond.
- Free-form ponds: draw the outline in the calculator, or trace it over a photo, survey or sketch of your yard.
Measure the hole after you dig it, not the plan. Holes almost always come out bigger. When you install the liner, don't pull it tight: lay it loose and let the water press it into the hole. A liner stretched during installation is the most common reason a liner looks too small.
Pond liner size chart
Liner sizes for common rectangular ponds, with 18 inches of edge overlap on every side. For an L-shaped or free-form pond, add 1 ft to each side before rounding, or draw it in the calculator.
| Pond | Size and deepest point | Liner to order | Area | RPE 30 mil | EPDM 45 mil | Underlayment |
|---|---|---|---|---|---|---|
| Small water garden | 6 x 4 ft, 1.5 ft deep | 10 x 15 ft | 150 sq ft | $97.50 | $160.50 | $61.50 |
| Garden pond | 8 x 6 ft, 2 ft deep | 15 x 15 ft | 225 sq ft | $146.25 | $240.75 | $92.25 |
| Garden pond | 10 x 8 ft, 2 ft deep | 15 x 20 ft | 300 sq ft | $195.00 | $356.00 | $123.00 |
| Fish pond | 10 x 10 ft, 2.5 ft deep | 20 x 20 ft | 400 sq ft | $260.00 | $545.25 | $164.00 |
| Small koi pond | 12 x 10 ft, 3 ft deep | 20 x 25 ft | 500 sq ft | $325.00 | $652.25 | $205.00 |
| Koi pond | 15 x 10 ft, 3 ft deep | 20 x 25 ft | 500 sq ft | $325.00 | $652.25 | $205.00 |
| Koi pond | 15 x 12 ft, 3.5 ft deep | 25 x 25 ft | 625 sq ft | $406.25 | $786.00 | $256.25 |
| Koi pond | 20 x 12 ft, 4 ft deep | 25 x 35 ft | 875 sq ft | $686.00 | $1,053.50 | $358.75 |
| Large koi pond | 20 x 15 ft, 4 ft deep | 30 x 35 ft | 1,050 sq ft | $799.75 | $1,240.75 | $430.50 |
Prices are our store prices in November 2026. The calculator always shows today's price.
How much does a pond liner cost?
Liner is priced by the square foot of the sheet you order:
- RPE 30 mil: $0.65 a square foot for most sheets, up to about $0.79 for the largest
- EPDM 45 mil: $1.07 to about $1.41 a square foot, depending on the sheet size
- Underlayment: $0.41 a square foot
For the 12 x 10 ft koi pond above, a 20 x 25 ft liner costs $325 in RPE or $652.25 in EPDM, plus $205 for underlayment.
Large ponds and lakes
The same formula works at any size. A one-acre pond (about 209 ft square) that is 6 ft deep needs roughly 224 x 224 ft of liner, about 50,000 square feet. Liner that size is made as fabricated panels, so ask us for a quote with your dimensions.
EPDM or RPE: which pond liner should you choose?
| EPDM 45 mil | RPE 30 mil Ultra | |
|---|---|---|
| Material | Synthetic rubber | Reinforced polyethylene with a laminated coating |
| Weight | 0.28 lb per sq ft | About 0.10 lb per sq ft |
| Price per sq ft | $1.07 to $1.41 | $0.65 to $0.79 |
| Warranty | 20 years exposed, 24 years covered | 20 years |
| Fish safety | Made for ponds with fish and plants | NSF/ANSI 61 certified, rated for drinking water |
| Best for | Small free-form ponds with tight curves, where the stretch helps it settle into the shape | Koi ponds and larger ponds, where a lighter sheet is easier to place and costs less |
EPDM is soft and stretchy, so it settles into curves and corners easily. RPE weighs about a third as much for the same area and costs roughly half to two-thirds as much, which matters more as the pond gets bigger. Our 30 mil RPE is our most popular koi pond liner. Compare every option in RPE pond liners and EPDM pond liners.
How thick should a pond liner be?
45 mil is the standard thickness for EPDM pond liner. RPE is reinforced with a woven scrim, so it does the same job thinner, and we sell it from 20 to 60 mil. For a koi pond, 30 mil RPE or 45 mil EPDM is the usual choice. Go thicker if the soil is rocky, if large stones will sit on the liner, or if people will walk in the pond. Good underlayment protects a liner more than a few extra mils do.
Do you need pond underlayment?
Yes. Underlayment is a felt-like fabric that goes between the soil and the liner and protects it from rocks and roots. Order the same size as your liner. Ours is 8 oz geotextile, twice the weight of the 4 oz fabric many kits include, and the calculator adds it to your order unless you take it off. See all pond underlayment.
Streams and waterfalls
Add a stream or waterfall in the calculator and you can line it with the pond's sheet or with its own piece. Separate pieces are laid top down: each one laps 12 inches over the liner below it, upstream piece on top, so the water runs over the joint and no seam tape is needed.
Box-welded drop-in liners
For a rectangular or round pond with straight sides, such as a raised pond, a tank or a formal pond, a box-welded liner is made to your exact size with factory-welded corners, so there are no folds or pleats. Drop-in liners are made to order and can't be returned, so measure twice. They line the pond only, so a stream or waterfall still needs a flat liner piece. See box-welded pond liners.
Common pond liner mistakes
- Using the average depth. Size from the deepest point.
- Leaving no edge. Allow at least 18 inches all round to anchor the liner under stone, edging or soil.
- Measuring the plan instead of the hole. Measure after you dig.
- Stretching the liner tight. Lay it loose and let the water settle it.
- Skipping underlayment. One sharp stone can mean a leak you have to drain the pond to find.
- Trimming too early. Fill the pond and let it settle before you cut off the extra edge.
Pond liner calculator FAQ
What size pond liner do I need?
Take the pond's length, add twice its deepest point and twice the edge overlap, then do the same for the width and round both up to the next 5 ft. A 10 x 10 ft pond that is 2.5 ft deep needs a 20 x 20 ft liner with 18 inches of overlap.
How much overlap should a pond liner have?
At least 18 inches (1.5 ft) on every side. Use 2 to 2.5 ft if you will bury the edge in a trench or hold it down with large stones.
How much does a pond liner cost?
At our November 2026 prices, 30 mil RPE costs $0.65 to $0.79 a square foot and 45 mil EPDM costs $1.07 to $1.41. A 20 x 25 ft liner for a 12 x 10 ft koi pond is $325 in RPE or $652.25 in EPDM.
Which pond liner is best for a koi pond?
30 mil RPE is our most popular koi pond liner: it is light, strong and costs roughly half to two-thirds as much as EPDM. 45 mil EPDM works well too, especially in small ponds with tight curves.
Do plant shelves change the liner size?
No. Size the liner from the deepest point. The liner that crosses a shelf is liner the bottom no longer needs, so the formula still covers it.
How thick should a pond liner be?
45 mil for EPDM. RPE is reinforced, so 30 mil RPE does the same job. Go thicker for rocky soil or heavy stone on the liner.
Can I join two pieces of pond liner?
Yes. Stream and waterfall pieces lap 12 inches over the liner below them with no tape. To join two sheets in the pond itself, use the seam tape made for that liner material.
Should I buy a bigger liner than the calculator says?
No need. The calculator already rounds up to the next 5 ft, and the edge overlap gives you room to adjust. Trim the extra once the pond is full.