Every rotary drum filter needs water flowing through it. How that water gets there, by gravity or by pump, is one of the most important decisions in a koi pond filtration build. The choice affects energy costs, plumbing complexity, equipment placement, and even how gently fish waste is handled on its way to the filter.
This guide explains both configurations, walks through the plumbing for each, and helps determine which approach fits a given pond. For a broader overview of RDF technology and sizing, see Play It Koi's complete rotary drum filter guide.
Gravity-Fed RDF: How It Works
In a gravity-fed configuration, water flows from the pond to the drum filter entirely under the force of gravity. No pump is needed to move water into the filter; the pond's water level is higher than the filter's inlet, and gravity does the work.
A gravity-fed RDF requires bottom drains installed at the lowest point of the pond. Water flows by gravity from the drains into the drum filter, with no pump between the pond and the filter. A settlement chamber between the drains and the drum is optional.
The Plumbing
A gravity-fed RDF requires bottom drains in the pond floor. These drains connect to buried pipe that runs from the pond to the drum filter. The critical requirement is an elevation difference: the pond's water surface must be higher than the drum filter's inlet. Typically, this means the filter sits in a below-grade vault or equipment room, or the pond is built at a higher elevation than the filter pad.
The pipe diameter matters. Gravity-fed lines are usually 4-inch (110mm) PVC, and the pipe run should be as short and straight as possible. Every elbow and extra foot of pipe adds friction that reduces flow. Most builds use one 4-inch line per bottom drain, with two bottom drains being standard for ponds over 3,000 gallons.
After passing through the drum filter, the mechanically filtered water drops into a pump chamber (a small sump below or beside the filter). From there, a return pump pushes water through the biological filtration stage and back to the pond. The key distinction is that the pump sits after the filter, not before it.
Advantages of Gravity-Fed
- Energy efficient: No pump has to lift dirty pond water up into the drum filter. The only pump in the system sits after the filter and moves water that has already been screened, so it stays cleaner and runs more efficiently.
- Gentler on waste: Pump impellers break solid fish waste into smaller particles that are harder to filter. Gravity flow delivers waste intact to the drum screen, which improves filtration efficiency.
- Bottom drains pull waste from the pond floor: The heaviest waste settles to the bottom. Gravity-fed systems pull this waste directly from where it accumulates.
Disadvantages of Gravity-Fed
- Requires bottom drains: Existing ponds without bottom drains cannot use a gravity-fed setup without significant modification.
- Elevation requirements: The filter must sit lower than the pond. This may require excavation for a filter vault or careful site planning during new construction.
- More complex plumbing: Below-grade pipe runs, proper slope, and a pump chamber add installation complexity and cost.
- Harder to retrofit: Converting an existing pump-fed pond to gravity-fed is a major project.
Pump-Fed RDF: How It Works
In a pump-fed configuration, a pond pump draws water from the pond (via a skimmer, bottom drain, or both) and pumps it up into the drum filter. The pump sits before the filter in the water flow path.
The Plumbing
A pump-fed setup is straightforward. A submersible or external pump pulls water from the pond and pushes it through a pipe to the drum filter's inlet. The filtered water exits the drum and flows by gravity to the next stage (biological filtration) and then back to the pond, or a second pump returns it.
Because the pump lifts the water, the filter does not need to sit at the pond's water level. It sits above the water line, at grade or on a pad next to the pond, so the filtered water can flow back by gravity. SeaSide, for example, sets the top of its pump-fed Eco-20 30 cm above the pond's maximum water level. This flexibility is the primary practical advantage of pump-fed plumbing.
Pipe diameter is typically 2-inch or 3-inch PVC, smaller than gravity-fed lines because the pump provides the flow energy rather than relying on gravity and pipe diameter.
Advantages of Pump-Fed
- Flexible placement: The filter can go anywhere there is a level surface and power above the pond's water line, with no vault to dig.
- Works with any pond: Existing ponds with skimmers, submersible pumps, or external pumps can add an RDF without structural pond modifications.
- Simpler plumbing: No below-grade pipe runs or pump chambers needed. Standard PVC from pump to filter.
- Easier to retrofit: Adding a pump-fed RDF to an existing pond needs no digging below the water line.
Disadvantages of Pump-Fed
- Higher energy costs: The feed pump runs continuously and has to lift dirty pond water up into a drum that sits above the pond's water line. A pump-fed drum is also rated lower than the same drum fed by gravity: FREEDrum says to use 65% of the gravity rating, and SeaSide rates its pump-fed units about 30% lower, so a pumped system may need a larger drum.
- Waste fragmentation: Pump impellers shred solid waste into smaller particles. Some of these smaller particles pass through the drum mesh, reducing overall filtration effectiveness. This is the single biggest technical drawback of pump-fed setups.
Which PIK Models Support Which Configuration?
Most rotary drum filters sold by Play It Koi support both gravity-fed and pump-fed installation, but check the specific model with its maker. These are the exceptions and details to know:
- SeaSide Aquatics (Eco and PP series): Every standalone drum comes in a gravity-fed and a pump-fed version. SeaSide rates the pump-fed units about 30% lower.
- FREEDrum: Every model except the FREE 20 supports both configurations; the FREE 20 is gravity-fed only. FREEDrum says to use 65% of the gravity rating for a pump-fed install.
- GC Tek NishikigoiRDF: Gravity-fed only. GC Tek says it should never be pump-fed.
- Nijikawa Niji-no-Taki: Pump-fed only, like all bakki shower systems.
- Oase BioTec ScreenMatic²: Pump-fed only. OASE designs it to be fed by a filter pump, with the filtered water returning to the pond by gravity, and its manual covers no gravity-fed setup.
- Oase ProfiClear Premium Compact: OASE makes separate pump-fed and gravity-fed versions, so order the one that matches the plumbing. Play It Koi lists the Compact-L in both.
Real-World Gravity-Fed Builds
Play It Koi customer Billy Ngo runs a SeaSide Aquatics PP-35 in a gravity-fed configuration. A 4-inch aerated bottom drain and a skimmer feed the PP-35 by gravity, each line with its own knife valve so he can balance the pull between them. The pump pulls clean water from the drum and pushes it through an AlphaONE 6.0 pressure filter and a UV clarifier, then back to the pond, part of it by way of a stream. Billy says he cleaned the pond once in an entire year.
Randy Tan also built his pond around a gravity-fed RDF. Three Rhino II aerated bottom drains feed the drum, which works with an AlphaONE 10.0 pressure filter and two SeaSide Aquatics bakki showers for combined mechanical and biological filtration.
Both builds share the elements that make gravity-fed systems work: aerated bottom drains feeding the drum by gravity, and a pump that sits after the filter and only handles screened water. For detailed plumbing guidance, see Play It Koi's RDF installation guide.
How to Decide: Gravity-Fed vs Pump-Fed
The decision often comes down to whether a pond is being built new or is an existing structure:
- New pond construction: Gravity-fed is almost always the better choice. The efficiency and superior waste handling justify the additional upfront plumbing work. Design the pond elevation and equipment area with gravity flow in mind from the start.
- Existing pond retrofit: If the pond already has bottom drains and the equipment area is below pond water level, gravity-fed is feasible. If not, pump-fed is the practical choice, and a pump-fed RDF is still a big upgrade over manual filtration methods.
- Budget-sensitive builds: Pump-fed setups cost less to install because the plumbing is simpler and no excavation is needed. But the ongoing electricity costs are higher. Over 5 to 10 years, a gravity-fed system may cost less overall.
Regardless of configuration, adding a rotary drum filter to a koi pond transforms water quality and reduces daily maintenance. For help choosing the right model, see Play It Koi's complete RDF guide or the brand-by-brand comparison.
Frequently Asked Questions
Can I convert a pump-fed RDF to gravity-fed later?
Technically yes, but it is a significant project. Converting to gravity-fed requires adding bottom drains to the pond (which usually means draining it), running below-grade plumbing, and creating an equipment area below the pond's water level. If there is any chance of going gravity-fed in the future, it is far easier and cheaper to install the bottom drains and plumbing during initial pond construction.
Does pump-fed filtration actually hurt water quality?
It reduces mechanical filtration effectiveness compared to gravity-fed, but pump-fed RDFs still deliver far better water quality than manual filtration methods like sieves or settlement chambers. The waste fragmentation from pump impellers means some fine particles pass through the drum mesh, but the overall result is still excellent. Many outstanding koi ponds run pump-fed RDFs with beautiful water clarity.
How much energy does a gravity-fed system save?
The savings come from where the pump sits and what it has to do. In a pump-fed system, the pump lifts dirty pond water up into a drum that sits above the pond's water line, and a pump-fed drum is rated lower than the same drum fed by gravity. In a gravity-fed system, the pump sits after the drum and moves only filtered water. To compare the two for a given pond, compare the wattage of the pump each layout needs for the same flow. For scale, a pump drawing 200 to 500 watts around the clock uses about 1,750 to 4,380 kWh a year, which costs about $315 to $790 at $0.18 per kWh (the EIA's current U.S. average, from July 2026 data, checked 2026-10-21).
What size bottom drains do I need for a gravity-fed RDF?
Standard koi pond bottom drains are 4 inches (110mm). Most gravity-fed RDF installations use one 4-inch bottom drain per 2,500 to 3,000 gallons of pond volume. A 5,000-gallon pond typically needs two bottom drains, each with its own 4-inch line running to the drum filter. A 4-inch gravity line tops out around 3,600 GPH, so size the pump to what the drain lines can deliver. The pipe runs should be as short and straight as possible, since every 90-degree elbow reduces flow. See the installation guide for detailed plumbing specifications.
Is the Oase ScreenMatic² the only pump-fed-only model?
No. The Oase BioTec ScreenMatic² and the Nijikawa Niji-no-Taki are both pump-fed only, and every GC Tek NishikigoiRDF and the FREEDrum FREE 20 are gravity-fed only. SeaSide Aquatics drums and the rest of the FREEDrum line support both gravity-fed and pump-fed configurations, and OASE makes the ProfiClear Premium Compact in separate pump-fed and gravity-fed versions.